Tekno RC TKR8300

Additional Technical Info Will Be Added When It Becomes Available. **
This is the 1/8 scale Glow Powered, Radio Controlled,
4WD Competition NB48.4 Buggy Kit from Tekno RC.
**Engine Shown in Photo is NOT Included. **
Chassis: CNC machined hard anodized lightened 7075 aluminum,
0.16" (4mm) thick, short overhang for better bump handling and
jump landing, adjustable brace system
Drive: Four wheel with CV driveshafts and captured pins on wheels
Clutch: Adjustable, four 7075 aluminum shoes
Clutch Bell: 13T CNC machined steel, CNC machined flywheel
Fuel Tank: 4.2oz (125cc), IFMAR legal integrated filter/clunk with
external nipple
Differentials: Three fluid filled adjustable light weight diffs
Suspension: Fully adjustable long travel, adjustable front arm
sweep and angle, front and rear sway bars, captured outer front and
rear hinge pins, adjustable hinge pin braces, narrow high roll
center rear hubs, new bearing supported spindle/carrier with
updated geometry and enhanced durability
Steering: Ball bearing equipped, narrow pivot steering posts,
adjustable steering stops for precise travel setting, new
bellcranks, with optional solid right bellcrank (no servo saver)
for increased steering response
Shocks: 16mm bore CNC machined hard anodized threaded aluminum
bodies, 4mm hardened steel polished shock shafts, CNC machine
tapered pistons, CNC aluminum shock caps, preload adjusters and
cartridge caps, Triple Guide Design for reduced shaft deflection,
new clamping spring perches w/captured shock boots, options for
vented cap, emulsion, or standard shock configurations
Front Shock Tower: 0.24" (6mm) CNC machined 7075 aluminum
Rear Shock Tower: 0.20" (5mm) CNC machined 7075 aluminum
Engine Mount: Adjustable
Brakes: CNC machined steel disc with semi-metallic pads
Wing: New high downforce Wing, adjustable LCG light weight mount
Radio Tray: Integrated with right mud guard allowing receiver &
battery to sit on chassis for lowest CG possible
Throttle Control: CNC machined assembly riding on ball bearings
Spur Gear: 48T steel
Ackerman: Adjustable, Ackerman describes the effect of the inside
front wheel turning faster than the outside front wheel during
turns, CNC aluminum Ackerman plate rides on precision ball bearings
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to
the chassis
Camber: Adjustable front and rear, camber refers to the angle of the
tops of the tires from vertical when viewed from front or behind
vehicle
NB48.4 Buggy Kit, Shock and Diff Oil, Threadlock, clear Body, 13T
Clutch Bell, 48T Spur Gear, High-Downforce Wing, Decals, Shock and
Diff Oil, Instructions
Radio: 2-3ch with high-torque/speed steering & throttle servos
Engine: .21 cu in (3.4cc) glow engine with tuned pipe
Receiver Battery: Hump configuration
Tires and Wheels: 1/8 scale buggy
Starter box & glow igniter
Polycarbonate safe spray or brush on paint
Building and track equipment
Vehicle;
length: 17.1" (435mm) without wing
width: 12-12.2" (306-310mm)
Wheelbase: 12.7-13.2" (323-335mm) adjustable
Dry Weight: 7.17lb (3260g), varies depending on equipment
Diff Ratio: F/R-12/39t, center-48t
RX Battery Box
2.3 x 1.4 x 1.3" (58.5 x 36 x 34.5mm)
Body;
length: 13.4" (340mm)
width: 7.2" (183mm)
height: 4" (102mm)
For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 8x16mm Front Diff 1 DTXC1585
2 8x16mm Center Diff 1 DTXC1585
2 8x16mm Rear Diff 1 DTXC1585
2 5x13mm Front Gearbox 1 TKRC5134
4 13x19mm Rear Hubs 2 TKRC3194
2 13x19mm Front Hubs 1 TKRC3194
2 8x14mm Front Hubs 1 DTXC1583
4 5x8mm Steering 2 DTXC1523
4 6x10mm Steering 2 DTXC1561
1 5x13mm Clutch 1 TKRC5134
1 5x11mm Clutch 1 DTXC1547
jxs 01/26/17