Tekno RC TKR5304

This is the 1/8 scale Glow Powered, Radio Controlled,
4WD Competition NB48.3 Buggy Kit from Tekno RC.
**Engine Shown In Picture Is NOT Included. **
New features compared to the original NB48 include:
Redesigned Suspension Geometry
Revised Chassis
New Front and Rear Arms
New Front and Rear Shock Towers & Mount Screws, & Revised Standoffs
New Extra Long Shocks, Clamping Spring Perches w/Captured Shock Boots
New Tapered Shock Pistons
New Rear Hubs
New Trailing Front Spindles and Spindle Carriers
New V2 Hinge Pin Braces and Inserts
Low Profile Wing Mount
Revised Bumper for Increased Ground Clearance
New Straight Turnbuckle Rod Ends
New Easily Adjustable Droop Screws
New Brake Linkage
New 46T Spur Gear
New Brake Pads and Discs
Longer Rear Sway Bar
Updated Setup Sheet for Improved Handling
Chassis: CNC machined hard anodized lightened 7075 aluminum,
0.16" (4mm) thick, short overhang for better bump handling and
jump landing, adjustable brace system
Drive: Four wheel with CV driveshafts and captured pins on wheels
Clutch: Adjustable, four 7075 aluminum shoes
Clutch Bell: 15T steel
Fuel Tank: 4.2oz (125cc)
Differentials: Three fluid filled adjustable light weight diffs
Suspension: Fully adjustable long travel, adjustable front arm
sweep and angle, adjustable length rear arms, front and rear sway
bars
Steering: Ball bearing equipped, narrow pivot steering posts,
adjustable steering stops for precise travel setting
Shocks: 16mm bore CNC machined hard anodized threaded aluminum
bodies, 4mm hardened steel polished shock shafts, CNC machine
tapered pistons, CNC aluminum shock caps, preload adjusters and
cartridge caps, Triple Guide Design for reduced shaft deflection,
new clamping spring perches w/captured shock boots, options for
vented cap, emulsion, or standard shock configurations
Shock Towers: 0.197" (5mm) CNC Machined 7075 Aluminum
Motor Mount: Dual position allows fast cornering or greater traction
Brakes: Steel disc with semi-metallic pads
Wing Mount: Adjustable, LCG light weight
Radio Tray: Integrated with right mud guard allowing receiver &
battery to sit on chassis for lowest CG possible
Throttle Control: CNC machined assembly riding on ball bearings
Spur Gear: 46T
Ackerman: Adjustable, Ackerman describes the effect of the inside
front wheel turning faster than the outside front wheel during
turns
CNC aluminum Ackerman plate rides on 4 precision ball bearings
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to
the chassis
Camber: Adjustable front and rear, camber refers to the angle of the
tops of the tires from vertical when viewed from front or behind
vehicle
NB48.3 Buggy Kit, Shock and Diff Oil, Threadlock, clear Body, 15T
Clutch Bell, 46T Spur Gear, High-Downforce Wing, Decals, Shock and
Diff Oil, Instructions
Radio: 2-3ch with high-torque/speed steering & throttle servos
Engine: .21 cu in (3.4cc) glow engine with tuned pipe
Receiver Battery: Hump configuration
Tires and Wheels: 1/8 scale buggy
Starter box & glow igniter
Polycarbonate safe spray or brush on paint
Building and track equipment
Vehicle;
length: 17.1" (435mm) without wing
width: 12-12.2" (306-310mm)
Wheelbase: 12.7-13.2" (323-335mm) adjustable
Dry Weight: 7.17lb (3260g), varies depending on equipment
Diff Ratio: F/R-10t, center-46t
RX Battery Box
2.3 x 1.4 x 1.3" (58.5 x 36 x 34.5mm)
Body;
length: 13.4" (340mm)
width: 7.2" (183mm)
height: 4" (102mm)
For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 8x16mm Front Diff 1 DTXC1585
2 8x16mm Center Diff 1 DTXC1585
2 8x16mm Rear Diff 1 DTXC1585
2 5x13mm Front Gearbox 1 TKRC5134
4 13x19mm Rear Hubs 2 TKRC3194
2 13x19mm Front Hubs 1 TKRC3194
2 8x14mm Front Hubs 1 DTXC1583
4 5x8mm Steering 2 DTXC1523
4 6x10mm Steering 2 DTXC1561
1 5x13mm Clutch 1 TKRC5134
1 5x11mm Clutch 1 DTXC1547
jxs 07/20/15
ir/jxs
&