Robart ROB608HD
$49.95
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.90 Degree 3/16 Wire Strut
This is a set of Robart 90 Degree Mechanical Main Retracts w/ 3/16" wire.
For .45-1.20 size gas powered models weighing 5-10 lbs (2.3-4.5kg).
Positive up and down locks
Tough glass-filled nylon construction
Light weight-5oz pair
3/16" Tempered steel gear legs
Mechanically operated with standard or "Retract" servos
Eight mounting screws
Installation instructions and spare parts list
Mounting to aircraft
2-56 threaded pushrod for operation
Approximately 1-1/8" of travel to operate retract from lock to lock
Possible cutting and bending of wire to proper length
SPEC: Total Length: 11-1/4" ( 286mm) closed, 11-1/8"(283mm) open
Width of base: 1-3/4" (44.45mm) x 1-3/4" (44.45mm)
On same side of retract, holes are 1-1/4" (31.75mm) center to center
Opposite side holes center to center: 1-11/32" (34.29mm)
Distance from edge of base to loop in closed position: 9/32" (8mm)
Distance from edge of base to loop in open position: 5/8"(16mm)
Diameter of loop: 21/32"(17mm)
Length of wire from loop: 8-1/2" (216mm)
Total height of base: 1-3/32" (27.94mm)
Thickness of mount lip: 3/32" (2.54mm)
Length of mount lip: 1-3/4" (44.45)
Width of base: 15/16" (24.13mm)
Height from bottom of base to center of control rod: 13/16" (21mm)
This retract operates with a 2-56 threaded pushrod. The pushrod
screws into the control arm and will push or pull the control arm
to operate the system.
For the Robart 90 Degree Mechanical Main Retracts w/ 3/16" wire,
order ROBQ0608
For the Robart Axle Adapter with 3/16" Axle for 3/16 wire struts,
order ROBQ0659
For .45-1.20 size gas powered models weighing 5-10 lbs (2.3-4.5kg).
FEATURES:
Tough glass-filled nylon construction
Light weight-5oz pair
3/16" Tempered steel gear legs
Mechanically operated with standard or "Retract" servos
YOU WILL RECEIVE:
Two main 90 degree retracts Eight mounting screws
Installation instructions and spare parts list
REQUIREMENTS:
2-56 threaded pushrod for operation
Approximately 1-1/8" of travel to operate retract from lock to lock
Possible cutting and bending of wire to proper length
SPEC: Total Length: 11-1/4" ( 286mm) closed, 11-1/8"(283mm) open
Width of base: 1-3/4" (44.45mm) x 1-3/4" (44.45mm)
On same side of retract, holes are 1-1/4" (31.75mm) center to center
Opposite side holes center to center: 1-11/32" (34.29mm)
Distance from edge of base to loop in closed position: 9/32" (8mm)
Distance from edge of base to loop in open position: 5/8"(16mm)
Diameter of loop: 21/32"(17mm)
Length of wire from loop: 8-1/2" (216mm)
Total height of base: 1-3/32" (27.94mm)
Thickness of mount lip: 3/32" (2.54mm)
Length of mount lip: 1-3/4" (44.45)
Width of base: 15/16" (24.13mm)
Height from bottom of base to center of control rod: 13/16" (21mm)
COMMENTS:
screws into the control arm and will push or pull the control arm
to operate the system.
For the Robart 90 Degree Mechanical Main Retracts w/ 3/16" wire,
order ROBQ0608
For the Robart Axle Adapter with 3/16" Axle for 3/16 wire struts,
order ROBQ0659
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov