Robart ROB551RSE
$279.95
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.Mini 85 Degree Mains Robostrut Ready Electric
This is a pair of 85 Electric Main Low Profile Robostrut Ready
Landing Gear from Robart.
Compatible with a 3/8" diameter RoboStrut (not included), or
3/16" diameter gear wire
Constructed of aircraft grade aluminum
Amp Out circuitry senses up/down travel limits or an obstruction such
as a gear door and shuts off the motor to prevent draining the
battery
One year warranty on parts, six months warranty on labor covering
manufacturing defects. Warranty void if controller box or actuators
are opened.
with Control Box and Instructions
4.8 - 9.0V from any battery type, (6V and above highly recommended)
Robart extensions from control board to retracts;
IMPORTANT, Robart electric retracts use a non-standard plug and
require the use of proprietary Robart extensions instead of
standard servo extensions. Please use the stock numbers below to
order the proper extensions.
ROBM0177 177E12 12" ELC RTRCT SERVO EXT (qty 2)
ROBM0178 177E12S 12" ELC RTRCT SERVO EX (qty 1)
ROBM0179 177E24 24" ELC RTRCT SERVO EXT (qty 2)
ROBM0180 177E24S 24" ELC RTRCT SRVO EXT (qty 1)
*
board use standard servo plugs.
Mounting Plate Length: 1-1/2" (38.1mm)
Mounting Plate Width: 1-3/4" (44.4mm)
Distance between Mounting Hole Centers: 1-3/8" (31mm) lengthwise
1" (25.4mm) widthwise
Length/end of Actuator to end of Mounting Frame: 3-7/16" (87.5mm)
Mounting Hole Diameter: 5/32" (4mm)
Landing Gear from Robart.
FEATURES:
3/16" diameter gear wire
Constructed of aircraft grade aluminum
Amp Out circuitry senses up/down travel limits or an obstruction such
as a gear door and shuts off the motor to prevent draining the
battery
One year warranty on parts, six months warranty on labor covering
manufacturing defects. Warranty void if controller box or actuators
are opened.
YOU WILL RECEIVE:
Two 85 Electric Main Low Profile Robostrut Ready Landing Gears, with Control Box and Instructions
REQUIREMENTS:
Robart extensions from control board to retracts;
IMPORTANT, Robart electric retracts use a non-standard plug and
require the use of proprietary Robart extensions instead of
standard servo extensions. Please use the stock numbers below to
order the proper extensions.
ROBM0177 177E12 12" ELC RTRCT SERVO EXT (qty 2)
ROBM0178 177E12S 12" ELC RTRCT SERVO EX (qty 1)
ROBM0179 177E24 24" ELC RTRCT SERVO EXT (qty 2)
ROBM0180 177E24S 24" ELC RTRCT SRVO EXT (qty 1)
*
NOTE:
The receiver and auxiliary battery inputs on the control board use standard servo plugs.
SPECIFICATIONS:
Mounting Plate Width: 1-3/4" (44.4mm)
Distance between Mounting Hole Centers: 1-3/8" (31mm) lengthwise
1" (25.4mm) widthwise
Length/end of Actuator to end of Mounting Frame: 3-7/16" (87.5mm)
Mounting Hole Diameter: 5/32" (4mm)
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov