Novak NOV3008

This is the Novak SS8.5 Pro Brushless Electric Motor and GTB Speed Control for Brushless Motors Racing System Specifically designed for cars and trucks, ROAR legal. SS8.5 Brushless Motor (NOVC3408); Sensor based design for excellent starting torque, continuous synchronization, low-speed driveability, consistent brakes and thermal protection Provides approximately 20% longer run-times than brushed motors One-piece design neodymium magnets provide high power and great reliability Nickel plated sintered neodymium rotor User-replaceable rotor, front end bell/bearing, and rear bearing Convenient solder tab system for easy wire replacement Thermal Overload Protection (when used with a Novak brushless ESC) Non-removable color timing ring Lightweight ribbed aluminum end bells Novak GTB Programmable Electronic Speed Control (NOVM1710); Four different color status LEDs for easy set-up, programming and profile selection 3 fully-programmable fwd/brake/ Brushless profiles 1 fully-programmable fwd/brake/ Brush motor profile 1 fully-programmable fwd/brake/rev Brushless motor profile 1 fixed-programming Limited Reverse (25%) profile Programming adjustments include; Min Drive, Min Brake, Drag Brake & Dead Band, Drive Frequency adjustable in the Brush-Mode Low profile high volume cooling fan and factory team Power Trans-Cap Module Gold plated PCB direct-solder tabs and 6-layer circuit boards for lowest possible voltage drop and easy power wire replacement User replaceable input harness, long and short input harnesses supplied Remote power programming switch combines one-touch button and ON/OFF switch, can be remotely mounted for easy programming adjustments and powering ESC ON and OFF Water-resistant case with complete gasketing for improved protection 120 day limited warranty on both components Novak GTB Programmable Electronic Speed Control with Factory Installed Power Wires and Power Trans Cap Module, User-Replaceable Remote Power Programming Switch and Input Harness (two lengths included), Instructions, double Sided Tape SS8.5 Brushless Motor Installing in vehicle SS8.5 Brushless Motor Turns: 8.5 Design: Sensor-based Motor Size: 540 Size: 2.08" L x 1.41" D (52.8 x 35.8mm) Weight: 6.61 oz. (187 grams) Input Voltage: 4-7 cells (1.2V/cell or 4.8-8.4 total volts) Magnet: Nickel-plated, Sintered, high-strength Neodymium Watts: 280 KV (unloaded): 5000 Shaft Diameter: 0.125" 3.2mm (accepts all existing pinion gears) Front Bearing Size: 1/2 x 3/16" (12.7 x 4.8mm) Protection: Thermal GTB Programmable Electronic Speed Control Size: L 1.49" (37.8mm), W 1.16" (29.5mm) Weight: 1.36oz (38.5g) without wires BEC: 6.0V/3.0A Input Voltage: 4-6 cells (1.2VDC/cell) *On Resistance (Brushless): 0.00040 ohms *On Resistance (Brush Mode): 0.00013 ohms *Rated Current (Brushless): 540A/phase *Rated Current (Brush Mode): 1620A Battery/Motor Wire:14AWG silicone Throttle Profiles: 6 (5 Brushless/1 Brush) Drive Frequencies: 1 of 7 (1.5-11kHz) Minimum Drive: 1 of 5 (2-12%) Minimum Brake: 1 of 10 (5-50%) Dead Band: 1 of 5 (2-6%) Braking Style: Std or Drag Brake Drag Brake: 1 of 10 (10-50%) Brushless Motor Limit: Any Novak Brushed Motor Limit: None *Transistor rating @ 25°C junction temp For replacement Trans-Cap Module, order NOVM5679. For a replacement Fan order NOVC5648, or NOVC5652 for a two-pack For replacement Remote Power Switch, order NOVM5602 jxs 5/08/07 ir/jxs &