MIP MIP18390
$55.67
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.MIP18390 X-Duty CVD Kit - TRA Bandit
This is an MIP Rear X-Duty CVD Drive Kit for the TRA Bandit.
Strong splined X-Duty steel construction
Strong 12mm Keyed Hex Standard (Must use 12mm wheels not compatible with pin)
Fully rebuildable so any damaged or worn part can be replaced. (scroll down on main part # and all rebuild components are there)
Ultimate upgrade for those that are drag racing!
No more ripped and twisted drivetrain.
Heat Treated steel components to help increase strength and part life
Black Oxide coated to protect the components from premature rust
100% Designed / Manufactured / Packaged in the USA
1x MIP Inst. Sheet, 18390 TRA Bandit
1x MIP Thread Gel Safety Sheet
1x MIP Support Parts Insert Sheet
1x MIP Lube & Thread Gel Cup
2x MIP Confetti Sticker
2x CVD Axles/TRA Slash Duty Rear
2x MIP X-Duty Female Bone, 40mm
2x MIP X-Duty, Drive Hub, 13mm w/ 5mm Bore
2x MIP X-Duty Male Bone, 42mm
2x shss/ M3 x 4mm Flat Point
2x Hex Adapter TRA X-Duty CVD Kit
4x MIP M4 Pin Screw Slash Diff
4x MIP Bearing Spacer, Rear, TRA Slash/ Slash 4x4
2x spacer/ HPI Blitz ft. bearing spacer
5x MIP 1/4" CVD Coupling
5x Ø.092 x .625 Cross Pin w/ flat
5x shss/ 8-32 x 1/8 flat point
2x nut/ m4x.7 steel nyloc
When hubs are in the lowest position, clearance on the arm may be necessary for the X-Duty Bell to rotate freely. Best to use a sanding drum to clearance the plastic arm. (check out photo with wrench pointing to area)
Use MIP Grease and threadlocking compound upon assembly.
Be sure to keep joints lubed to enjoy long part life
Front TRA 12mm Hex Conversion : 1 x TRA1654
Upgrade Hubs and Bearings recommended : TRA3752 , TRA5116
FEATURES:
Strong splined X-Duty steel construction
Strong 12mm Keyed Hex Standard (Must use 12mm wheels not compatible with pin)
Fully rebuildable so any damaged or worn part can be replaced. (scroll down on main part # and all rebuild components are there)
Ultimate upgrade for those that are drag racing!
No more ripped and twisted drivetrain.
Heat Treated steel components to help increase strength and part life
Black Oxide coated to protect the components from premature rust
100% Designed / Manufactured / Packaged in the USA
YOU WILL RECEIVE:
1x MIP Inst. Sheet, 18390 TRA Bandit
1x MIP Thread Gel Safety Sheet
1x MIP Support Parts Insert Sheet
1x MIP Lube & Thread Gel Cup
2x MIP Confetti Sticker
2x CVD Axles/TRA Slash Duty Rear
2x MIP X-Duty Female Bone, 40mm
2x MIP X-Duty, Drive Hub, 13mm w/ 5mm Bore
2x MIP X-Duty Male Bone, 42mm
2x shss/ M3 x 4mm Flat Point
2x Hex Adapter TRA X-Duty CVD Kit
4x MIP M4 Pin Screw Slash Diff
4x MIP Bearing Spacer, Rear, TRA Slash/ Slash 4x4
2x spacer/ HPI Blitz ft. bearing spacer
5x MIP 1/4" CVD Coupling
5x Ø.092 x .625 Cross Pin w/ flat
5x shss/ 8-32 x 1/8 flat point
2x nut/ m4x.7 steel nyloc
NOTES:
When hubs are in the lowest position, clearance on the arm may be necessary for the X-Duty Bell to rotate freely. Best to use a sanding drum to clearance the plastic arm. (check out photo with wrench pointing to area)
Use MIP Grease and threadlocking compound upon assembly.
Be sure to keep joints lubed to enjoy long part life
Front TRA 12mm Hex Conversion : 1 x TRA1654
Upgrade Hubs and Bearings recommended : TRA3752 , TRA5116
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov