HPI HPI105938

This is the 1/10 scale glow powered, radio controlled, ready to run HPI Nitro RS4 3 Evo+ with the 1970 Plymouth 'Cuda body. Chassis: 0.098" (2.5mm) 6061 aluminum, gray in color Drive: Four wheel shaft drive Engine: Nitro Star G3.0 3.0cc (.18 cu in) 2.2hp with Roto-Start can be bump started in racing applications) ABC cylinder and liner construction-"A"luminum piston,"B"rass cylinder liner that is "C"hrome plated, lightweight aluminum con rod, 2 needle 6.5mm rotary carburetor, 2 stage air filter Exhaust: Dual chamber aluminum tuned pipe, black in color Radio: 2.4GHz 3-channel with steering and throttle trims, dual rate for steering and charge jack for optional NiCd battery Servos: Two standard size and torque Fuel Tank: 2.53oz (75cc), flip top cap Clutch: 2-shoe Transmission: Two-speed, adjustable Ball Bearings: 18 rubber sealed Shocks: Four oil-filled, with coil-over spring Main Gear: 47 and 43 tooth composite construction main gears Clutch bell: 22 teeth and 18 teeth gears that thread onto clutch bell Gearbox: Sealed, front and rear Differentials: Sealed, with metal bevel gears, limited slip front differential Brake: Single disc, fiber construction Tires: D compound X-pattern 1.02" (26mm) wide, 2.5" (65mm) diameter Wheels: Vintage 5-spoke matte finish chrome 6-Cell Flat Battery Pack: 7.2V 2000mAh for Roto Start Battery Charger: Wall type for Roto Start battery Fuel Bottle: 8.4oz (250cc) Glow Starter: C size with C-cell battery included Body: Pre-painted and trimmed with rear wing and decals applied, and extra clear wing Bumper: Front foam Suspension: Four wheel independent double wishbone Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle Steering: Bellcrank Servo Saver: Included HPI RS4 3 Evo+ oil-filled shocks, tuned pipe, 3.0cc engine, trimmed and painted polycarbonate body, tires, foam inserts, wheels, decals 2.4GHz 3-ch radio, Roto-Start & battery, wall charger, 10 AA batteries, fuel bottle, glow starter w/battery, instructions, glow plug and wrench Building and track equipment Fuel: 2-stroke glow fuel with 10%-20% nitromethane, 16% lubricant- Most of the fuels we carry meet or exceed the lubricant content required for optimum performance and maximum engine life. In the past, the conventional lubricant content used in fuel was 18%. But with new advanced technologies, fuels like Red Alert and O'Donnell for example, have a better quality of lubricants even though the percentages of lubricant content are lower. These high-tech lubricants provide exceptional cooling and protection. Vehicle- Length: 17.1" (434mm) Width: 7.9" (200mm) Height: 4" (102mm) Weight: 3.85lbs (1745g) approximate Wheelbase: 10.1" (256mm) (wheels on-center front-to-rear) Tread: Front-6.75" (171mm) Rear-7" (178mm) (wheels on-center side to-side) Front Track: 7.25" (184mm) Rear Track: 7.75" (197mm) Ground Clearance: 0.29" (7.5mm) Body- Length: 17.5" (444mm) Width: 7.5" (190mm) Height: 4" (102mm) For Replacement Ball Bearings use: Qty. Size Location Qty. Bearing Set (2) 10 x 15mm spur gear shaft 1 DTXC1595 (4) 5 x 11mm front & rear gearbox 2 DTXC1547 (4) 10 x 15mm front & rear gearbox 2 DTXC1595 (2) 5 x 11mm front wheel hubs 1 DTXC1547 (2) 10 x 15mm front wheel hubs 1 DTXC1595 (4) 5 x 11mm rear wheel hubs 2 DTXC1547 (2) 5 x 10mm clutch bell 1 DTXC1535 For an optional engine from O.S. the .18CV-RX (OSMG2104) and the Complete One-Piece Pipe (OSMG2988) can be used. jxs 07/28/11 ir/jxs &