HPI HPI707
$249.99
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.SPRINT 2 RTR W/HPI IMPREZA BODY *
This is the 1/10 scale electric powered, radio controlled, Ready To Run
HPI Sprint 2 on-road Touring Car with the Impreza Body.
_
Chassis: Reinforced molded nylon chassis, upper deck and shock towers
Drive: Four wheel
Drive Type: Urethane belt
Motor: Tornado 17 turn
Radio: HPI (made by AiRTRonics) AM TX-2 pistol grip with steering and
throttle trim, dual rate adjustment, charge jack and servo reverse,
standard size servo
Electronic Speed Control: Hawk Power Reverse
Full ball bearings: Located in transmission and bell crank, rubber
sealed bearings in wheels, 14 total
Shocks: Four oil-filled, plastic bodied
Differentials: Planetary gear type with metal outdrives, sealed
Transmission: Ball bearing equipped and capable of handling modified
motors down to 10 turns
Wheels: 6 spoke chrome 1 (26mm) wide, 2 (51mm) diameter, 6mm offset
at rear, 3mm offset at front
Tires: X-pattern D compound 1 (26mm) wide 2.5 (64mm) outer diameter
Bumpers: Front, foam
Body: Fully trimmed and painted with rear wing and decals applied
Battery: 1800mAh 7.2V 6-cell with standard connector, chassis also
accepts saddle pack batteries
Charger: AC wall, charges battery in six hours
Suspension: Fully adjustable
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Ackerman: Adjustable, Ackerman describes the effect of the inside
front wheel turning tighter than the outside front wheel
Steering: Bell-crank type with servo saver
HPI Sprint 2 on-road Touring Car with oil-filled shocks, 17 turn
motor, Electronic Speed Control, painted body, tires, foam inserts
wheels, 28 tooth pinion gear, 87 tooth spur gear, instructions, 2-
channel radio, 1800mAh battery pack, AC wall charger, 2 and 3° rear
toe-in blocks, 4 and 6° front caster blocks, Sprint 2 decal sheet
AA batteries: 8 for transmitter
Misc. Items: Building and track equipment
VEHICLE-
length: 17 (431mm)
width: 7.5 (190mm)
height: 5 (127mm)
Weight: 3.1lbs (1425g) ready-to-run
Wheelbase: 10 (254mm)
Front Tread: 6.5 (166mm)
Rear Tread: 6.9 (175mm) side-to-side at wheel centers
Front Track: 7.3 (186mm)
Rear Track: 7.75 (197mm)
Ground Clearance: 0.41 (10.5mm)
Gear Ratio: 6.62:1
Tires- Front and Rear: 1 x 2.5 (26mm x 64mm)
BODY-
length: 17 (432mm)
width: 8.2 (208mm) at rear wheels (widest point)
7.25 (184mm) ahead of front wheels (thinnest point)
height: 3.5 (89mm)
For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
4 5x10mm Front Wheels 2 DTXC1535
4 5x10mm Rear Wheels 2 DTXC1535
2 4x8mm Servo Saver 1 DTXC1511
2 5x8 Fr Diff Shafts 1 DTXC1523
2 5x8 R Diff Shafts 1 DTXC1523
2 10x15mm Fr Ball Diff 1 DTXC1595
2 10x15mm R Ball Diff 1 DTXC1595
Body pictured on the box is painted orange and yellow.
HPI Sprint 2 on-road Touring Car with the Impreza Body.
_
FEATURES:
Chassis: Reinforced molded nylon chassis, upper deck and shock towers
Drive: Four wheel
Drive Type: Urethane belt
Motor: Tornado 17 turn
Radio: HPI (made by AiRTRonics) AM TX-2 pistol grip with steering and
throttle trim, dual rate adjustment, charge jack and servo reverse,
standard size servo
Electronic Speed Control: Hawk Power Reverse
Full ball bearings: Located in transmission and bell crank, rubber
sealed bearings in wheels, 14 total
Shocks: Four oil-filled, plastic bodied
Differentials: Planetary gear type with metal outdrives, sealed
Transmission: Ball bearing equipped and capable of handling modified
motors down to 10 turns
Wheels: 6 spoke chrome 1 (26mm) wide, 2 (51mm) diameter, 6mm offset
at rear, 3mm offset at front
Tires: X-pattern D compound 1 (26mm) wide 2.5 (64mm) outer diameter
Bumpers: Front, foam
Body: Fully trimmed and painted with rear wing and decals applied
Battery: 1800mAh 7.2V 6-cell with standard connector, chassis also
accepts saddle pack batteries
Charger: AC wall, charges battery in six hours
Suspension: Fully adjustable
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Ackerman: Adjustable, Ackerman describes the effect of the inside
front wheel turning tighter than the outside front wheel
Steering: Bell-crank type with servo saver
INCLUDES:
HPI Sprint 2 on-road Touring Car with oil-filled shocks, 17 turn
motor, Electronic Speed Control, painted body, tires, foam inserts
wheels, 28 tooth pinion gear, 87 tooth spur gear, instructions, 2-
channel radio, 1800mAh battery pack, AC wall charger, 2 and 3° rear
toe-in blocks, 4 and 6° front caster blocks, Sprint 2 decal sheet
REQUIREMENTS:
AA batteries: 8 for transmitter
Misc. Items: Building and track equipment
SPECIFICATIONS:
VEHICLE-
length: 17 (431mm)
width: 7.5 (190mm)
height: 5 (127mm)
Weight: 3.1lbs (1425g) ready-to-run
Wheelbase: 10 (254mm)
Front Tread: 6.5 (166mm)
Rear Tread: 6.9 (175mm) side-to-side at wheel centers
Front Track: 7.3 (186mm)
Rear Track: 7.75 (197mm)
Ground Clearance: 0.41 (10.5mm)
Gear Ratio: 6.62:1
Tires- Front and Rear: 1 x 2.5 (26mm x 64mm)
BODY-
length: 17 (432mm)
width: 8.2 (208mm) at rear wheels (widest point)
7.25 (184mm) ahead of front wheels (thinnest point)
height: 3.5 (89mm)
COMMENTS:
For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
4 5x10mm Front Wheels 2 DTXC1535
4 5x10mm Rear Wheels 2 DTXC1535
2 4x8mm Servo Saver 1 DTXC1511
2 5x8 Fr Diff Shafts 1 DTXC1523
2 5x8 R Diff Shafts 1 DTXC1523
2 10x15mm Fr Ball Diff 1 DTXC1595
2 10x15mm R Ball Diff 1 DTXC1595
Body pictured on the box is painted orange and yellow.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov