HPI HPI104819

HPI brand 1/10 scale, electric powered, radio controlled, ready-to-run HPI On-Road Sprint 2 Drift Car with the 2010 Chevy Camaro Body. FEATURES: Chassis: 3/16 (4mm) thick plastic Drive: Four wheel belt drive Motor: 15 turn, aluminum motor mount Radio: HPI TF-1 pistol grip AM 27MHz with steering and throttle trim and reverse and SF-1 steering servo, transmitter has charge jack Ball Bearings: Full set included Shocks: Oil-filled, aluminum bodied with special drifting springs Differentials: Planetary gear with metal outdrives Transmission: Single speed Tires: Falken hard plastic drift tires, width 1.02 (26mm), 2.5 (63mm) diameter Wheels: Officially licensed 5-spoke Volk wheels with 6mm offset, outer diameter: 1.9 (48mm), width: 1.0 (26mm) Speed Control: Electronic, SC-15 with reverse Pinion Gear: 28 tooth 48 pitch metal Spur Gear: 48 pitch, 87 tooth, composite construction Body: Painted and trimmed 2010 Camaro Bumper: Front, foam Suspension: Fully adjustable Ackerman: Adjustable, Ackerman describes the effect of the inner front wheel turning faster than the outer front wheel during turns Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable front and rear, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle Steering: Ball race bell-crank type with servo saver Warranty: Two year limited warranty through HPI beginning at purchase date. Valid only in the USA, Canada and South America YOU WILL RECEIVE: HPI On-Road Drift 2010 Camaro with brushed motor, electronic speed control, painted body, drift tires, wheels, 28 tooth pinion gear 87 tooth spur gear, 2-ch radio, steering servo, decal sheet and instructions _ REQUIRES: Radio Batteries: (8) AA size Battery: 6-cell 7.2V stick with standard connector, chassis accepts stick or saddle packs Battery Charger: Peak type recommended Paint: Polycarbonate safe spray or brush-on Misc. Items: Building and track equipment SPECS: VEHICLE- Length: 17 (431mm) Width: 7.5 (190mm) Height: 5 (127mm) Wheelbase: 10 (255mm) Front Track: 7.38 (187.5mm) side to side at outer edges of wheel Rear Track: 7.7 (197mm) Front Tread: 6.5 (166mm) Rear Tread: 7.2 (183mm) side-to-side at wheel centers Ground Clearance: 0.5 (13mm) BODY- Length: 17.1 (434mm) Width: 7.75 (197mm) at rear wheels (widest point) 6.6 (169mm) behind from wheels (thinnest point) Height: 4.4 (111mm) COMMENTS: For Replacement Ball Bearings use: Qty. Size Location Qty. Bearing Set 4 5x10mm Fr Wheels 2 DTXC1535 4 5x10mm Rear Wheels 2 DTXC1535 2 10x15mm Fr Diff 1 DTXC1595 2 2x8mm Fr Diff 1 DTXC1523 2 10x15mm Rear Diff 1 DTXC1595 2 2x8mm Rear Diff 1 DTXC1523 2 4x8mm Servo Saver 1 DTXC1511 2 4x8mm Middle Lay Shaft 1 DTXC1511 Available with the following 27MHz radio channels; A1 HPID05A1 A4 HPID05A4 A2 HPID05A2 A5 HPID05A5 A3 HPID05A3 A6 HPID05A6 jxs 09/03/10 ir/jxs