HPI HPI10054

This is the 1/10 scale glow powered, radio controlled, Ready To Run
HPI Nitro RS4 3 Evo+ with the 67 Covett body.

Chassis: 0.098" (2.5mm) 6061 aluminum, purple in color
Drive: Four wheel shaft drive
Engine: Nitro Star G3.0 3.0cc (.18 cu in) 2.2hp with pull-starter,
can be bump started in racing applications) ABC cylinder and liner
construction-"A"luminum piston, "B"rass cylinder liner that is
"C"hrome plated, lightweight aluminum con rod, 2 needle 6.5mm
rotary carburetor, 2 stage air filter.
Exhaust: Dual chamber aluminum tuned pipe with tube header, black in
color
Radio: Two channel 27MHz AM with steering and throttle trims, dual
rate for steering and charge jack for optional NiCd battery
Servos: Two standard size and torque
Fuel Tank: 2.53oz (75cc), flip top cap
Clutch: 2-shoe
Transmission: Two-speed, adjustable
Ball Bearings: 18 rubber sealed
Shocks: Four oil-filled, with coil-over spring
Main Gear: 47 and 43 tooth composite construction main gears
Clutch bell: 22 teeth and 18 teeth gears that thread onto clutch bell
Gearbox: Sealed, front and rear
Differentials: Sealed, with metal bevel gears, limited slip front
differential
Brakes: Single disc, fiber construction
Tires: D compound X-pattern 1.02" (26mm) wide, 2.5" (65mm) diameter
Wheels: Vintage 5-spoke matte finish chrome
Body: Pre-painted and trimmed with rear wing and decals applied
Bumper: Front foam
Suspension: Four wheel independent
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Steering: Bellcrank
Servo Saver: Included

HPI RS4 3 Evo+ oil-filled shocks, tuned pipe, 3.0cc engine, trimmed
and painted polycarbonate body, tires, foam inserts, wheels, decals
AM 27MHz 2-ch radio, Roto-Start and instructions

AA Batteries: 12 (8 for radio, 4 for battery box)
6-Cell Flat Battery Pack: For Roto Start
Battery Charger: For Roto Start battery
Track Equipment: Fuel bottle, glow starter
Fuel: 2-stroke glow fuel with 10%-15% nitromethane, 16% lubricant-
Most of the fuels we carry meet or exceed the lubricant content
required for optimum performance and maximum engine life. In the
past, the conventional lubricant content used in fuel was 18%. But
with new advanced technologies, fuels like Red Alert and O'Donnell
for example, have a better quality of lubricants even though the
percentages of lubricant content are lower. These high-tech
lubricants provide exceptional cooling and protection.

length: 17.1" (434mm)
width: 7.9" (200mm)
height: 4" (102mm)
Weight: 3.85lbs (1745g) approximate
Wheelbase: 10.1" (256mm) (wheels on-center front-to-rear)
Tread: Front-6.75" (171mm) Rear-7" (178mm) (wheels on-center side
to-side)
Front Track: 7.25" (184mm)
Rear Track: 7.75" (197mm)
Ground Clearance: 0.29" (7.5mm)

For Replacement Ball Bearings use:
Qty. Size Location Bearing Set Qty.
(2) 10 x 15mm spur gear shaft (use 1 DTXC1595)
(4) 5 x 11mm front & rear gearbox (use 2 DTXC1547)
(4) 10 x 15mm front & rear gearbox (use 2 DTXC1595)
(2) 5 x 11mm front wheel hubs (use 1 DTXC1547)
(2) 10 x 15mm front wheel hubs (use 1 DTXC1595)
(4) 5 x 11mm rear wheel hubs (use 2 DTXC1547)
(2) 5 x 10mm clutch bell (use 1 DTXC1535)
The Nitro 3 EVO+ with 'Cuda body is available in the following
channels;
A1 HPID53A1
A2 HPID53A2
A3 HPID53A3
A4 HPID53A4
A5 HPID53A5
A6 HPID53A6
For an optional engine from O. S. Max, the .18CV-RX (OSMG2104) and the
Complete One-Piece Pipe (OSMG2988) can be used.
jxs 03/16/07
UPD JiM 04.17.07
ir/jxs
If you need more information, use these HPI Racing resources E-mail: support@HPIracing. com
Web Site: https: //www. HPIracing. com/
Phone: 949-753-1099
Postal Address:
HPI Racing
70 ICON STREET
FOOTHILL RANCH, CA 92610
Click here for Units of Measure Conversion Calculators