Hot Bodies HBS66861

This is the radio controlled glow powered, ready to run Hot Bodies Lightning Pro 2 Off Road Buggy with Red Body. Chassis: Aluminum 0.12" (3mm) thick (purple anodized) Drive: Four wheel, shaft driven Radio: HPI TF-1 27MHz AM with high torque steering servo, steering and throttle trim and reverse, dual rate steering, transmitter does not have charge jack Engine: HPI .28 cu in (4.6cc) Power House big block engine with electric starter Exhaust: Tuned pipe with header Fuel Tank: Plastic with flip top cap, splash guard and overflow drain 5.1 oz (150cc) Clutch: Three shoe, 13 tooth metal clutch bell and purple aluminum flywheel Transmission: Single-speed Ball Bearings: Rubber sealed, used throughout except servo saver where bushings are used Shocks: Four aluminum bodied, oil filled with coil-over springs, plastic shock spacers, and 3.5mm hardened shock shafts 7075 (T6) 4mm thick front and rear shock towers (purple anodized) Main Gear: Metal, 46 tooth Gearbox: Sealed front and rear Differentials: Bevel gear (hardened) Brake: Dual disk on the front and single disk on the rear Tires: 1.6" (41mm) wide, 3" (76mm) inner diameter, 4.75" (121mm) outer diameter knobby tread rubber with foam inserts pre-glued to wheels Wheels: White dish plastic 1.6" (41mm) wide, 3" (76mm) diameter Body: Painted polycarbonate plastic buggy with nylon rear racing wing Bumpers: Black plastic partial front bumper Suspension: Front and rear sway bars Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable front and rear, camber refers to the angle of the tops of the tires from vertical when when viewed from front or behind vehicle Steering: Bell-crank type with two steering link mounts for Ackerman adjustability, Ackerman refers to the inside wheel turning faster that the outside wheel during turns Servo Saver: Included 22 degree hub carriers Front CVA axles and rear dog bones Center CVA shafts (front and rear) Machined aluminum front and rear braces (purple anodized) Front and rear sway bars One Hot Bodies Lightning 1/8 scale RTR buggy with oil-filled aluminum bodied shocks, painted body with wing, air filter, 46 tooth tooth main gear, tuned pipe, manifold with spring, fuel tubing, engine, radio system, setup DVD, decal sheet, 4 way wrench, 13 tooth clutch bell, and illustrated instruction manual Starter Battery: 7.2V stick 6-cell with Tamiya type connector AA Batteries: 12AA Fuel: 2-cycle glow fuel with 10%-15% nitromethane, 16% lubricant. Most of the fuels we carry meet or exceed the lubricant content required for optimum performance and maximum engine life. In the past, the conventional lubricant content used in fuel was 18%. But with new advanced technologies, fuels like Red Alert and O'Donnell for example, have a better quality of lubricants even though the percentages of lubricant content are lower. These high-tech lubricants provide exceptional cooling and protection. Glow starter, fuel bottle and track equipment Vehicle- Length: 22.9" (582mm) Width: 16.4" (416mm) Height: 6.25" (159mm) Weight: 7.2 lbs (3275g) approx Wheelbase: 14.5" (369mm) wheels on-center front-to-rear Front and Rear Tread: 14" (356mm) Front and Rear Track: 16.1" (410mm) Ground Clearance: 2" (51mm) Gear Ratio: 3.6 :1 Body- Length: 18.1" (460mm) Width: 7.1" (181mm) Height: 5.1" (130mm) For replacement ball bearings use: Qty. Size Location Qty. Bearing Set 8 8x16x5mm Fr & Rear Wheel Hubs 4 HPIC2085 6 8x16x5mm Fr, Rear & Center Diffs 3 HPIC2085 2 5x10mm Clutch 1 DTXC1535 jxs 5/12/08 ir/jxs &