Futaba FUTM0099
$20.00
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.discontinued s5801 sail winch servo
This is a Sail Control Winch Servo that has proper Winching Action with a
Drum (rather than servo arms like other "sail winch" servos).
This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable
of delivering sufficient amps.
High Torque and High Speed
BEC set-up (a 5-6 cell pack powers the winch and the receiver
the same way an Electronic Speed Control would)
Water Resistant
5-pole motor
Metal Gears
Two Ball Bearing
Adjustable Trimmer (adjusts from two to six 360° revolutions) as
increasing number of revolutions are dialed in, speed increases
(Futaba J Receiver Plug, ON/OFF Switch and Tamiya-style battery plug)
One Drum Adjuster Plastic Screwdriver
One Illustrated Instructions Sheet
5-6 Cell Battery w/Tamiya Connector, use DTXC1900.
Torque: 108 oz-in @ 6V - 136 oz-in @ 7.2V
(7.8 kg-cm @ 6V - 9.8 kg-cm @ 7.2V)
Servo Speed: 0.60 sec/360° rotation @ 6V
0.50 sec/360° rotation @ 7.2V
Drum Travel: 2 to 6 Revolutions (adjustment range)
Drum Diameter: 1.6" (42mm)
Length: 1.8" (1-13/16")(46mm) excluding drum and mount flanges
Width: 1.0" (1") (25mm)
Height: 1.7" (1-3/4") (44mm)
Weight: 2.9oz (2-15/16oz) (83g)
Power Requirement: 6.0 - 7.2V NiCd battery (5 - 6 cells)
Regulator output: 6.0V/1.5A (max) (power to the receiver)
Drum Measurements:
Height: 9mm (.356")
Width: 41.9mm (1.652")
Width of each groove: 3.5mm (.140")
Depth of each groove:13.7mm (.540")
Drum (rather than servo arms like other "sail winch" servos).
This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable
of delivering sufficient amps.
FEATURES:
BEC set-up (a 5-6 cell pack powers the winch and the receiver
the same way an Electronic Speed Control would)
Water Resistant
5-pole motor
Metal Gears
Two Ball Bearing
Adjustable Trimmer (adjusts from two to six 360° revolutions) as
increasing number of revolutions are dialed in, speed increases
YOU WILL RECEIVE:
One S5801 Sail Winch Servo(Futaba J Receiver Plug, ON/OFF Switch and Tamiya-style battery plug)
One Drum Adjuster Plastic Screwdriver
One Illustrated Instructions Sheet
REQUIREMENTS:
SPECIFICATIONS:
(7.8 kg-cm @ 6V - 9.8 kg-cm @ 7.2V)
Servo Speed: 0.60 sec/360° rotation @ 6V
0.50 sec/360° rotation @ 7.2V
Drum Travel: 2 to 6 Revolutions (adjustment range)
Drum Diameter: 1.6" (42mm)
Length: 1.8" (1-13/16")(46mm) excluding drum and mount flanges
Width: 1.0" (1") (25mm)
Height: 1.7" (1-3/4") (44mm)
Weight: 2.9oz (2-15/16oz) (83g)
Power Requirement: 6.0 - 7.2V NiCd battery (5 - 6 cells)
Regulator output: 6.0V/1.5A (max) (power to the receiver)
Drum Measurements:
Height: 9mm (.356")
Width: 41.9mm (1.652")
Width of each groove: 3.5mm (.140")
Depth of each groove:13.7mm (.540")
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov