e-Flite EFLA1040B
$69.99
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.40-Amp Pro Switch-Mode BEC Brushless ESC (V2)
Features
Up to 40 amps continuous current with proper air flow and 55 amps burst current (15 seconds)
5A continuous current, 5V Switch-Mode BEC Circuit (Proper cooling and airflow required)
Stronger BEC for support of most 3-axis stabilization systems
Drive up to 7 analog or 6 digital standard-sized servos with the BEC
3- to 6-cell Li-Po, 9- to 18-cell Ni-MH/Ni-Cd input voltage
Finned heat sinks
Programmable motor braking
Safe power-arm mode prevents accidental starts
Programmable low voltage cutoff with settings for 3-cell Li-Po (9V), 4-cell Li-Po (12V), 5-cell Li-Po (15V), 6-cell Li-Po (18V) or 70% of battery starting voltage
Programmable throttle input range
Programmable soft start for helis and airplanes
Auto motor shut down if signal is lost or there is interference
Programmable timing5 user-selectable ranges to use with a large variety of brushless motors
Utilizes new smaller Mosfet technology to minimize weight
Radio System Power ON /OFF Switch
Prewired connectorsE-flite EC3 connector on battery input and 3.5mm gold bullet connectors on motor output leads
Overview
E-flite 40-Amp Pro Switch-Mode BEC Brushless ESC (V2) is a high-quality sensorless brushless electronic speed control with an integrated switch-mode BEC that is very lightweight and efficient. It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication.
Specifications
Continuous Maximum Current
40A (Proper cooling and airflow required)
Input Voltage
36S Li-Po or 918 Ni-MH/Ni-Cd
Input Connector Types
13 AWG with E-flite EC3 Connector
Output Connector Types
13 AWG with 3.5mm Gold Bullet Connectors
Momentary Peak Current
55A (15 sec) (Proper cooling and airflow required)
Length
68.0mm (2.70 in)
Width
33.0mm (1.30 in)
Height
13.0mm (0.50 in)
Weight
62.0 g (2.20 oz)
Up to 40 amps continuous current with proper air flow and 55 amps burst current (15 seconds)
5A continuous current, 5V Switch-Mode BEC Circuit (Proper cooling and airflow required)
Stronger BEC for support of most 3-axis stabilization systems
Drive up to 7 analog or 6 digital standard-sized servos with the BEC
3- to 6-cell Li-Po, 9- to 18-cell Ni-MH/Ni-Cd input voltage
Finned heat sinks
Programmable motor braking
Safe power-arm mode prevents accidental starts
Programmable low voltage cutoff with settings for 3-cell Li-Po (9V), 4-cell Li-Po (12V), 5-cell Li-Po (15V), 6-cell Li-Po (18V) or 70% of battery starting voltage
Programmable throttle input range
Programmable soft start for helis and airplanes
Auto motor shut down if signal is lost or there is interference
Programmable timing5 user-selectable ranges to use with a large variety of brushless motors
Utilizes new smaller Mosfet technology to minimize weight
Radio System Power ON /OFF Switch
Prewired connectorsE-flite EC3 connector on battery input and 3.5mm gold bullet connectors on motor output leads
Overview
E-flite 40-Amp Pro Switch-Mode BEC Brushless ESC (V2) is a high-quality sensorless brushless electronic speed control with an integrated switch-mode BEC that is very lightweight and efficient. It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication.
Specifications
Continuous Maximum Current
40A (Proper cooling and airflow required)
Input Voltage
36S Li-Po or 918 Ni-MH/Ni-Cd
Input Connector Types
13 AWG with E-flite EC3 Connector
Output Connector Types
13 AWG with 3.5mm Gold Bullet Connectors
Momentary Peak Current
55A (15 sec) (Proper cooling and airflow required)
Length
68.0mm (2.70 in)
Width
33.0mm (1.30 in)
Height
13.0mm (0.50 in)
Weight
62.0 g (2.20 oz)
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov