Robart ROB810RSE
$259.95
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.100 Degree Rotating Retract Set Electric
Robart brand pair of Robart 100? Rotating Electric Retracts
Electric Main Retracts with Control Unit.
FEATURES:
Designed for RC aircraft weighing 8 - 18lbs (3.6 - 8.2kg)
Constructed with heat treated aluminum alloy frames and trunions
Electric retract control unit may be operated from any battery type
with 4.8-9.0 volts (6.0V and above is highly recommended)
Amp-Out circuitry shuts off motor if an obstruction is detected
Warranty: One year parts, six months labor covering manufacturing
defects. Warranty void if Electric Retract Controller box or
actuators are opened or modified.
YOU WILL RECEIVE:
Two 100? Rotating Electric Retracts, Wire Leads and Connectors,
Control Unit, .020oz (6ml) bottle of Threadlock and Instructions
REQUIREMENTS:
If using 3/8 diameter RoboStruts, the #650SA 3/8 - 7/16 Sleeve
Adapters must be used
4.8-9.0 volt battery for control unit
SPECIFICATIONS:
Width of Mounting Plates in line with Actuator: 1-29/32 (48.5mm)
Width of Mounting Plates opposite of Actuator: 1-19/32 (40.1mm)
Mounting Hole Centers in line with Actuator: 1-17/32 (39mm)
Mounting Hole Centers opposite of Actuator: 1 (25.1mm)
Mounting Hole Diameter: 5/32 (4mm)
Mounting Plate Thickness: 3/32 (2.3mm)
Mounting Plate Width at Actuator: 31/32 (24.9mm)
Side Frame Height: 1-1/4 (31.8mm)
Length, back of Side Frame to end of Actuator: 4-5/32 (105.3mm)
Actuator Wire Lead Length: 12 (304.8mm)
COMMENTS
Do not connect retracts directly to receiver. Only for use with the
Control Box supplied by Robart. Failure to use control box
supplied by Robart with result in damage to actuator as well as
other electronics and will not be covered under warranty.
jxs 11/18/14
ir/jxs
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Electric Main Retracts with Control Unit.
FEATURES:
Designed for RC aircraft weighing 8 - 18lbs (3.6 - 8.2kg)
Constructed with heat treated aluminum alloy frames and trunions
Electric retract control unit may be operated from any battery type
with 4.8-9.0 volts (6.0V and above is highly recommended)
Amp-Out circuitry shuts off motor if an obstruction is detected
Warranty: One year parts, six months labor covering manufacturing
defects. Warranty void if Electric Retract Controller box or
actuators are opened or modified.
YOU WILL RECEIVE:
Two 100? Rotating Electric Retracts, Wire Leads and Connectors,
Control Unit, .020oz (6ml) bottle of Threadlock and Instructions
REQUIREMENTS:
If using 3/8 diameter RoboStruts, the #650SA 3/8 - 7/16 Sleeve
Adapters must be used
4.8-9.0 volt battery for control unit
SPECIFICATIONS:
Width of Mounting Plates in line with Actuator: 1-29/32 (48.5mm)
Width of Mounting Plates opposite of Actuator: 1-19/32 (40.1mm)
Mounting Hole Centers in line with Actuator: 1-17/32 (39mm)
Mounting Hole Centers opposite of Actuator: 1 (25.1mm)
Mounting Hole Diameter: 5/32 (4mm)
Mounting Plate Thickness: 3/32 (2.3mm)
Mounting Plate Width at Actuator: 31/32 (24.9mm)
Side Frame Height: 1-1/4 (31.8mm)
Length, back of Side Frame to end of Actuator: 4-5/32 (105.3mm)
Actuator Wire Lead Length: 12 (304.8mm)
COMMENTS
Do not connect retracts directly to receiver. Only for use with the
Control Box supplied by Robart. Failure to use control box
supplied by Robart with result in damage to actuator as well as
other electronics and will not be covered under warranty.
jxs 11/18/14
ir/jxs
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov