Associated ASCLRP8083
$194.99
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.*** ESC Quantum Competit
This is the LRP Quantum Competition 2 Digital Electronic Speed Control
that is distributed in the USA by Team Associated.
Ultra High Performance using latest SMD-Mosfets(Transistors)
Super-light for improved chassis handling
Forward-only with brake
Three-wire, motor/battery wire set-up
Small in size
Pre-set factory
D. E. M. S. - LRP's digital motor management
Automatic Start
Battery recharge during braking
FET Servo Lead, for powering an FET Servo
Extra strong Brake-Power
Real-time braking
Standard Battery Connector(Tamiya-style)
Bullet-style Motor Connectors
Motor & Battery wires pre-soldered
Fully waterproof and shock resistant
REVOlutionary reactive software
Lowest resistence for minimized losses and maximum power
LRP's improved Digital Engine Mapping system 2
100% digital technology with 3 adjustable modes.
Limited lifetime warranty
One Quantum Competition 2 ESC w/S-style radio connector
(for Hitec, JR, and AiRTRonics "Z" radio systems).
One Futaba J style connector
One AiRTRonics style connector(Old, pre-"Z" style)
One Adjusting stylus, used for high-speed and set-up adjustments
Three .1uf capacitors
One polarized Schottky diode
Three small 4" zip-ties
Two 3.5"x5" LRP decal sheets
Mounting tape
User guide
TRIC5500(no-solder connectors) if needed, to attach motor
wires from speed control.
Length of case: 1.1" (28.7mm)
Width of case: 1" (25.7mm)
Height of case: 0.56" (14.4mm)
Length of motor & battery wires: 10" (254mm)
Length of receiver lead-wire: 7.5" (191mm)
Length of on/off switch wire: 4" (102mm)
Voltage range: 4-7 cells (4.8v-8.4v)
Internal resistance: .00043 ohms
Momentary load: 235 amps
Pulse frequency: 3140Hz
Brief load: 150 amps
Continuous load: 80 amps
Recommended motor limit: 5+ turns
Receiver voltage: 5.8 volts
Max. receiver current(30 sec): 2.8 amps
Continuious receiver current(5 min): 1.4 amps
Weight: 061oz (17.5g)
Schottky diode and capacitors will need to be soldered to motor
This speed control has a three-wire system. The red wire will
need to be spliced into a "Y-cord" to be used as a positive(+)
lead for both the battery and the motor.
mcw-12/3/03
ir/jxs
this information was sourced from Great Planes Model Distributors
that is distributed in the USA by Team Associated.
FEATURES:
Ultra High Performance using latest SMD-Mosfets(Transistors)
Super-light for improved chassis handling
Forward-only with brake
Three-wire, motor/battery wire set-up
Small in size
Pre-set factory
D. E. M. S. - LRP's digital motor management
Automatic Start
Battery recharge during braking
FET Servo Lead, for powering an FET Servo
Extra strong Brake-Power
Real-time braking
Standard Battery Connector(Tamiya-style)
Bullet-style Motor Connectors
Motor & Battery wires pre-soldered
Fully waterproof and shock resistant
REVOlutionary reactive software
Lowest resistence for minimized losses and maximum power
LRP's improved Digital Engine Mapping system 2
100% digital technology with 3 adjustable modes.
Limited lifetime warranty
INCLUDES:
One Quantum Competition 2 ESC w/S-style radio connector
(for Hitec, JR, and AiRTRonics "Z" radio systems).
One Futaba J style connector
One AiRTRonics style connector(Old, pre-"Z" style)
One Adjusting stylus, used for high-speed and set-up adjustments
Three .1uf capacitors
One polarized Schottky diode
Three small 4" zip-ties
Two 3.5"x5" LRP decal sheets
Mounting tape
User guide
REQUIREMENTS:
TRIC5500(no-solder connectors) if needed, to attach motor
wires from speed control.
SPECIFICATIONS:
Length of case: 1.1" (28.7mm)
Width of case: 1" (25.7mm)
Height of case: 0.56" (14.4mm)
Length of motor & battery wires: 10" (254mm)
Length of receiver lead-wire: 7.5" (191mm)
Length of on/off switch wire: 4" (102mm)
Voltage range: 4-7 cells (4.8v-8.4v)
Internal resistance: .00043 ohms
Momentary load: 235 amps
Pulse frequency: 3140Hz
Brief load: 150 amps
Continuous load: 80 amps
Recommended motor limit: 5+ turns
Receiver voltage: 5.8 volts
Max. receiver current(30 sec): 2.8 amps
Continuious receiver current(5 min): 1.4 amps
Weight: 061oz (17.5g)
COMMENTS:
Schottky diode and capacitors will need to be soldered to motor
This speed control has a three-wire system. The red wire will
need to be spliced into a "Y-cord" to be used as a positive(+)
lead for both the battery and the motor.
mcw-12/3/03
ir/jxs
this information was sourced from Great Planes Model Distributors
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov