Tekno RC TKR5005

This is the 1/8 scale, Electric Powered, Radio Controlled,
EB-48.3 Buggy Kit from Tekno RC.
New Features Include;
Completely Redesigned Suspension Geometry
New Front and Rear Arms
New Front and Rear 7075 CNC Aluminum Shock Towers
New Extra Long Shocks for Increased Suspension Travel
New Tapered 4 x 1.8mm Shock Pistons
New Clamping Spring Perches with Captured Shock Boots
New Rear Hubs
New Trailing Front Spindles and Spindle Carriers
New V2 Hinge Pin Braces and Inserts
Low Profile Wing Mount
Revised Bumper for Increased Ground Clearance
New Split Center Differential Mount
New Straight Turnbuckle Rod Ends
New Tapered Aluminum Front Center Driveshaft
New Left and Right Hand Threaded Shock Mount Screws
New Easily Adjustable Droop Screws
Revised Shock Standoffs for Easier Droop Measurement
Longer Rear Sway bar for More Consistent Traction
Updated Chassis With Increased Clearance for V2 Hinge Pin Settings
Updated Setup Sheet for Improved Handling
Chassis: CNC aluminum, 0.16" (4mm) thick, adjustable brace system for
fine tuning flex with front, center, and rear braces
Drive: Four wheel shaft, tapered aluminum center driveshaft
Motor Mount: Two-piece CNC aluminum construction with dual clamping
gear mesh adjusment, light weight direct to diff mount design
accomodates truggy or long can motors up to 3.1" (78mm) long
Differentials: Three light weight fluid filled bevel gear type,
updated low wear cross pin design, new ring and pinion gears for
smoother operation
Battery Tray: Sunken into chassis for super low center of gravity,
tray accomodates one 4S or two 2S LiPo packs
Shocks: 16mm big bore, oil filled, CNC threaded shock bodies, caps,
cartridge caps, and adjustment nuts, 4mm hardened steel polished
shafts, options for vented cap, emulsion, or standard shock
configurations, updated internals to minimize shaft deflection
new tapered piston design
Shock Towers: 6mm front, 5mm rear CNC 7075 aluminum, anodized gun-
metal gray in color
Body: Clear polycarbonate buggy, with white plastic high-downforce
wing
Suspension: Adjustable front arm sweep and angle, equal length front
and rear sway bars, adjustable length arms to suit any track
conditions, updated front and rear XT arms
Steering: Narrow pivot posts provide zero bump geometry with nearly
zero slop, CNC aluminum Ackerman plate rides on 4 precision
bearings, adjustable bump-steer and Ackerman, Ackerman describes
the effect of the inside front wheel turning faster than the
outside front wheel during turns, adjustable steering stops
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to
the chassis, has +1.5 rear outer toe plate for more adjustability
Camber: Adjustable front and rear, camber refers to the angle of the
tops of the tires from vertical when viewed from front or behind
vehicle
EB-48.3 Electric Buggy Kit with Body, Rear Wing, Motor Mount, Shocks,
Shock and Diff Oil, Decals and Instruction Manual
Radio: 2-3 channel with high-speed steering servo (also, standard
servo if using brake)
Motor: brushless type designed for 1/8 scale buggies
Pinion Gear: Mod 1, Tekno RC 11 - 30t recommended
LiPo Battery: One 4S or two 2S
Tires: 1/8 scale buggy
Wheels: 1/8 scale buggy
Battery Charger: For selected LiPo battery
Paint, tools and track equipment
Buggy-
length: 17.1" (435mm)
Wheelbase: 12.7-13.2" (323-335mm)
width: 12" (306mm), 12.2" (310mm) with optional hubs
Weight: 7.5lbs (3400g) with common electronics & options
Diff Ratio: F/R 10/40t, Center 44t
Battery Tray
1.96 x 5.8" (50 x 148mm) 2x2s or 1x4s config
Body-
length: 13" (330mm)
width: 5" (127mm)
height: 3.1" (80mm)
For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 8x16mm Ctr. Diff 1 DTXC1585
2 8x16mm Front Diff 1 DTXC1585
2 8x16mm Rear Diff 1 DTXC1585
2 5x11mm Fr Gearbox 1 DTXC1547
2 5x11mm Rear Gearbox 1 DTXC1547
2 13x19mm Rear Hubs 1 ARZC2636
2 8x16mm Rear Hubs 1 DTXC1585
2 13x19mm Front Hubs 1 ARZC2636
2 8x14mm Front Hubs 1 DTXC1583
4 5x8mm Steering 2 DTXC1523
jxs 07/02/15
&