Hobbico HCAP2522
$19.99
in stock? NO
This item is on back-order. It's difficult to know when it will be available to ship.discontinued Hot-Shot 2 Long
Hobbico brand Hot-Shot #2 Long Glo-Starter with Battery Charger.
This is used to heat glow plugs while starting glow-powered engines.
Proven Twist and Lock Connector ensures a secure, solid connection
that won't come off, providing safer, faster starts for your model.
Pre-Installed Genuine Sanyo Sub-C battery cell
Included AC battery charger with hex-shaped charge end recharges
the Glow Starter in 10 hours. A red LED glows as unit is charging.
Removable Red rubber socket cap prevents shorting and any dirt or
dust debris from entering into the the shaft.
One Year Limited Warranty USA and Canada only
One Hot Shot #2 Long Glo-Starter w/Red rubber protective cap
One Hot Shot #2 Glo-Starter Battery Charger
One Instruction/Header Card
Sanyo Sub-C NiCd Battery: 1500mAh, 1.2V
AC Charger- Input: 110-120V AC 60Hz (US Standard)
Output: 1.25V DC 150mA
Hot Shot- Overall length: 5-7/8 (149mm) Shaft length: 3-3/4 (95mm)
diameter: 15/16 (24mm)
COMMENTS
How to use: To lock onto your engine's glow plug, place the end of
the Hot Shot 2 over the plug and push down. Twist the Hot Shot 2
clockwise and it locks into place.
Charging: Before using, initial charge should be 12 to 14 hours
Subsequent charging time is approximately 10 hours
For Hot Shot #2 Standard version use HCAP2520
For Super Hot Shot #2 version use HCAP2528
**********The charger that was originally packaged with this Glo-Starter
had a 150mAh charge rate which requires a long time to charge the
large mAh battery. The customer charges the battery initially
for 12 hours; 24 hours for more frequent fliers.
JAL 8/20/99
ir/jl
This is used to heat glow plugs while starting glow-powered engines.
FEATURES:
Proven Twist and Lock Connector ensures a secure, solid connection
that won't come off, providing safer, faster starts for your model.
Pre-Installed Genuine Sanyo Sub-C battery cell
Included AC battery charger with hex-shaped charge end recharges
the Glow Starter in 10 hours. A red LED glows as unit is charging.
Removable Red rubber socket cap prevents shorting and any dirt or
dust debris from entering into the the shaft.
One Year Limited Warranty USA and Canada only
YOU WILL RECEIVE:
One Hot Shot #2 Long Glo-Starter w/Red rubber protective cap
One Hot Shot #2 Glo-Starter Battery Charger
One Instruction/Header Card
SPECIFICATIONS:
Sanyo Sub-C NiCd Battery: 1500mAh, 1.2V
AC Charger- Input: 110-120V AC 60Hz (US Standard)
Output: 1.25V DC 150mA
Hot Shot- Overall length: 5-7/8 (149mm) Shaft length: 3-3/4 (95mm)
diameter: 15/16 (24mm)
COMMENTS
How to use: To lock onto your engine's glow plug, place the end of
the Hot Shot 2 over the plug and push down. Twist the Hot Shot 2
clockwise and it locks into place.
Charging: Before using, initial charge should be 12 to 14 hours
Subsequent charging time is approximately 10 hours
For Hot Shot #2 Standard version use HCAP2520
For Super Hot Shot #2 version use HCAP2528
**********The charger that was originally packaged with this Glo-Starter
had a 150mAh charge rate which requires a long time to charge the
large mAh battery. The customer charges the battery initially
for 12 hours; 24 hours for more frequent fliers.
JAL 8/20/99
ir/jl
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov